Method Selection
Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.
提供各种无机材料、钢铁、有色金属、硬质合金陶瓷材料中宽范围的氧氮氢同时测定。湖南美国分析仪供应商
氧氮氢分析仪的常见故障及解决方法：
氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。 山东进口分析仪氧氮氢分析仪选哪家？给你推荐上海禹重科技！
ONH836系列：氧氮氢分析仪（熔融法）
软件特点和优势
Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可以快速导航和组织。工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。分析软件同时包括实时的环境参数的监测，提供完整的系统图表模拟。高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。
Sample Preparation
Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and
chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.
高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。
ONH836系列：氧氮氢分析仪（熔融法）
力可ONH836系列仪器采用惰性熔融法，提供各种无机材料、钢铁、有色金属、硬质合金、陶瓷材料中宽范围的氧氮氢同时分析。
ONH836系列仪器通过***采纳客户的反馈意见和创新设计，力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性、降低了分析成本、节省实验室桌面空间。
用户友好界面的Cornerstone™ 软件
力可**的Cornerstone 氧氮氧分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone 氧氮氧分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算，减少了繁琐的额外数据处理。
氧氮氢分析仪选哪家？给您推荐上海禹重！安徽进口分析仪多少钱
力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性、降低了分析成本、节省实验室桌面空间。湖南美国分析仪供应商
Oxygen, Nitrogen, and Hydrogen in Refractory Metals
Summary
One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a
hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent
cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps
such as heat treating, pickling, and cleaning.
The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry.
This application note was written specifically for use with the LECO ONH836 series determinator.
上海禹重实业有限公司位于友东路237号1幢104室。公司自成立以来，以质量为发展，让匠心弥散在每个细节，公司旗下光谱仪，色谱仪，质谱仪，样品前处理深受客户的喜爱。公司注重以质量为中心，以服务为理念，秉持诚信为本的理念，打造仪器仪表良好品牌。禹重科技凭借创新的产品、专业的服务、众多的成功案例积累起来的声誉和口碑，让企业发展再上新高。
