上海专业元素分析仪供应商

Instrument Highlights and Features

Optional Features

Optional boom-mounted touch-screen interface package (M) promotes an ergonomic workspace

Optional Performance Package (P) adds a three-stage carrier gas purification system, and a dual-loop gas dose module

Optional Dual Cooling Package (D) adds an integratedliquid-to-air radiator with dual cooling fans. This DC

option gives the user the choice of liquid-to-liquid cooling, liquid-to-air cooling, or a combination of both

Optional integrated autocleaner (H) automatically cleans the upper electrode and lower electrode tip

Optional 20-sample shuttle loader available

Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。上海专业元素分析仪供应商

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

浙江专业元素分析仪价格上海禹重给您提供各种氧氮氢分析仪，欢迎来电咨询！

ONH836系列：氧氮氢分析仪（熔融法）

软件特点和优势

Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可以快速导航和组织。工具条、滑动条和下拉式菜单简化了校正和数据处理的参数设定。分析软件同时包括实时的环境参数的监测，提供完整的系统图表模拟。高级诊断程序包括全数字化的在线操作手册、维护模拟演示、图片说明等提供快速指导。Cornerstone氧氮氢分析软件同时支持***的数据文档格式和可变的报告格式。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of three Standard reps.

Weigh approximately *** grams of a calibration/drift standard into a *** Nickel Capsule; enter the mass and standard identification into appropriate rep fields. If applicable, place the nickel capsule in the appropriate autoloader position.

Note: LECO Reference Materia***o not require preparation. See preparation statement on the reference material certificate. Solid Standards may be used to calibrate when chip or powder standards are not available.

高性能的红外检测器配置***恒温绝热技术，消除了外界环境温度的干扰。

氧氮氢分析仪

氧氮氢分析仪是一种用于材料科学领域的仪器，于2016年03月09日启用。

技术指标

测量范围： ON 低氧0.0－300ppm OH 低氧0.0－300ppm 高氧0.0－2% 高氧0.0－2% 低氮0.0―300ppm 低氢0.0－50ppm 高氮0.0－2% 高氢0.0－1000ppm 灵敏度： 氧0.01ppm；氮0.1ppm；氢0.01ppm。

主要功能

该仪器配置有16位微处理器和两个**的分别检测高氧和低氧的 红外检测池。氮和氢通过双重范围的热导检测池测量。分析过程中可自动实现从 低范围到高范围的切换。样品在高功率脉冲炉的石墨坩埚中加热可达3000℃以上 高温，脉冲炉采用循环水冷却。该仪器具有灵敏度高、性能好、测量范围宽和分 析结果准确可靠等优点。ONH-2000氧氮氢分析仪是为快速、准确测定铜、钢、铸 铁、合金、钛、镍、钼、锆、陶瓷和其它无机材料中氧、氮、氢的含量而专门设计 制造的。 采用三个**的红外器检测氧含量，同时检测CO和CO2，然后在转化为CO2集中检测。江苏元素分析仪厂家直销

Cornerstone氧氮氢分析软件分成4个主要部分：分析、诊断、设定、仪器，界面可快速导航和组织。上海专业元素分析仪供应商

氧氮氢分析仪的使用注意事项：

1 、氧氮氢分析仪在初次启用前，应该对连接点、焊点、阀门等进行检漏，以确保空气中的氧不会反渗进入管道及仪器内部，造成测量数值偏高。

2、再次使用仪器前，要进行管道系统净化，将漏入的空气除干净，同时确保连接取样管路时没有漏入空气。

3、样气中氧含量的变化会受管道材质及表面粗糙度影响，因此一般连接管路选用铜管或抛光过的不锈钢管，而不用塑料管、橡胶管等。

4、微量元素分析时，要避免各种管件、阀门、表头等死角对样气造成污染，因此必须尽可能的简化气路系统，连接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及腊封等设备，才能较好的确保数据的。

上海专业元素分析仪供应商