氧氮氢分析仪
氧氮氢分析仪是一种用于材料科学领域的仪器，于2016年03月09日启用。
技术指标
测量范围： ON 低氧0.0－300ppm OH 低氧0.0－300ppm 高氧0.0－2% 高氧0.0－2% 低氮0.0―300ppm 低氢0.0－50ppm 高氮0.0－2% 高氢0.0－1000ppm 灵敏度： 氧0.01ppm；氮0.1ppm；氢0.01ppm。
主要功能
该仪器配置有16位微处理器和两个**的分别检测高氧和低氧的 红外检测池。氮和氢通过双重范围的热导检测池测量。分析过程中可自动实现从 低范围到高范围的切换。样品在高功率脉冲炉的石墨坩埚中加热可达3000℃以上 高温，脉冲炉采用循环水冷却。该仪器具有灵敏度高、性能好、测量范围宽和分 析结果准确可靠等优点。ONH-2000氧氮氢分析仪是为快速、准确测定铜、钢、铸 铁、合金、钛、镍、钼、锆、陶瓷和其它无机材料中氧、氮、氢的含量而专门设计 制造的。 国际**的非色散红外及热导检测器 ，无移动部件，不需要手动调整。浙江美国LECO分析仪供应商
Oxygen, Nitrogen, and Hydrogen in Refractory Metals
Summary
Titanium is a metal that can be combined with elements such as aluminum, vanadium, molybdenum, and tin to produce high-strength, lowdensity, and corrosion-resistant alloys. Titanium alloys are used by the military, medical devices, sporting goods, and aerospace industries because of these properties, and due to the strict demands of these industries, effort needs to be taken to assure that the material meets the highest of quality standards.
安徽专业分析仪厂家供应可选具有压力补偿和温度控制性能的标气检测气路。
氧氮氢分析仪的使用注意事项：
1 、氧氮氢分析仪在初次启用前，应该对连接点、焊点、阀门等进行检漏，以确保空气中的氧不会反渗进入管道及仪器内部，造成测量数值偏高。
2、再次使用仪器前，要进行管道系统净化，将漏入的空气除干净，同时确保连接取样管路时没有漏入空气。
3、样气中氧含量的变化会受管道材质及表面粗糙度影响，因此一般连接管路选用铜管或抛光过的不锈钢管，而不用塑料管、橡胶管等。
4、微量元素分析时，要避免各种管件、阀门、表头等死角对样气造成污染，因此必须尽可能的简化气路系统，连接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及腊封等设备，才能较好的确保数据的。
Procedure - Solid Samples：
--Instrument calibration/drift correction.
Place the nickel basket containing the calibration/drift standard into the open port at the top of the loading head.
Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.
Clean the upper and lower electrode manually, or, if applicable, remove the crucible and press the analyze button to clean with the automatic cleaner.
Summary
The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high
mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power
electrode furnace to quickly and efficiently release the target gases from within the sample, which allows
for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.
减少了繁琐的额外数据处理。广东分析仪
可选六轴可旋转触摸屏幕，增强了操作的工效和直观性。浙江美国LECO分析仪供应商
ONH836系列：氧氮氢分析仪（熔融法）
力可ONH836系列仪器采用惰性熔融法，提供各种无机材料、钢铁、有色金属、硬质合金、陶瓷材料中宽范围的氧氮氢同时分析。
ONH836系列仪器通过***采纳客户的反馈意见和创新设计，力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性、降低了分析成本、节省实验室桌面空间。
用户友好界面的Cornerstone™ 软件
力可**的Cornerstone 氧氮氧分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone 氧氮氧分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算，减少了繁琐的额外数据处理。
浙江美国LECO分析仪供应商
