力可OHN736&836系列仪器采用惰性熔融法，提供各种无机材料、钢铁、有色金属、硬质合金陶瓷材料中宽范围的氧氮氢同时测定。ONH836仪器通过***采纳客户的反馈意见和创新设计，力可***仪器采用触摸屏技术和在线软件平台，增强了仪器的可操作性，降低了分析成本，节省实验室桌面空间。
用户友好界面的Cornerstone™ 软件
力可**的Cornerstone碳硫分析软件采用触摸屏界面使用户可完整的达到分析控制、方法设定、在线诊断、数据报告。Cornerstone碳硫分析软件允许用户在单一分析界面中完成日常的所有工作，快速而且简单易用。力可创新的批次和重复样品数据分组功能极大简化了样品结果输出和结果标准偏差的自动计算。减少了繁琐的额外数据处理。
长寿命的红外发射光源和无漂移的电路设计保证检测器的长期稳定性。山东美国分析仪多少钱
Procedure – Powder/Chip Samples
Instrument calibration/drift correction.
Calibrate/drift following the procedure outlined in the operator's instruction manual.
Login Sample with the appropriate number of reps.
Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the
appropriate autoloader position.
Repeat steps 3c through 3i for sample analysis.
氧氮氢分析仪的常见故障及解决方法：
氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。
Method Selection
Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.
高性能的红外检测器配置***恒温绝热技术，消除了外界环境温度的干扰。
Sample Preparation
Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and
chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.
配置SmartLine® Remote远程诊断功能。安徽专业分析仪厂家供应
力可**的动态流量补偿控制DFC系统，保证了流量系统的完善，可以精确控制整个气路中的流量。山东美国分析仪多少钱
仪器仪表行业本身是一个加入，产出周期较长的行业，所以作为业内厂家，一方面要寻找中、短期市场热点，另一方面也要在产品、技术研发方面有长远的规划;随着互联网的逐步发展，为光谱仪，色谱仪，质谱仪，样品前处理等产品的传播提供了一个飞速的平台。让仪器仪表行业从传统的销售模式到以互联网电子商务为主的营销方式的转变，促进了仪器仪表行业与互联网的结合，推动产业创新发展。目前我国从事仪器科技、医疗科技、检测科技领域内的技术咨询、技术服务，仪器仪表的修理，仪器仪表、实验室设备、机械设备及配件、机电设备及配件、电子产品、化工产品及原料（除危险化学品、监控化学品、烟花爆竹、民用易爆物品、易制毒化学品）、第二类医疗器械的销售，机械设备租赁，电子商务，货物进出口，技术进出口。产品，主要集中在中低档市场，而市场则主要被国外品牌所占据。在某些领域，国产产品甚至是空白，这就需要未来我国仪器仪表向市场进军，扩大产品占比。仪器仪表在工业发展中具有重要作用，这也使得仪器仪表得到快读发展。各行各业对仪器仪表的市场需求也在不断提升，贸易企业正在发展中寻求技术创新和质量提升。仪器仪表的质量、性能关系到工业安全，必须重视。山东美国分析仪多少钱
